ATYPICAL TREATMENT OF TOPWET
Technical requirements for the parameters of atypical cuffs for individual products may vary. It is therefore imperative to consult each atypical foil with our technical department at the contacts listed below:
Technical support for the Czech Republic and the Slovak Republic
Phone: +420 720 960 137
E-mail: [email protected]
Stock availability of atypical cuffs must always be checked with TOPWET. If the required cuff is not in stock, it must be delivered to the company address.
Atypically modified products cannot be returned under any circumstances.
custom cuff
(TPO/FPO, EPDM, ECB, EVA)
with or without braces
cutting the hem of the drain body
for a width of approx. 250 mm
(for XL width approx. 315 mm)
custom cuff
(TPO/FPO, EPDM, ECB, EVA)
with or without braces
extension up to 50 m, also applies to heated products (E)
custom cuff
(TPO/FPO, EPDM, ECB, EVA)
with or without braces
custom cuff
(TPO/FPO, EPDM, ECB, EVA)
with or without braces
trimming the trim of the body of the attachment
for a width of approx. 250 mm
(for XL width approx. 315 mm)
custom cuff
(TPO/FPO, EPDM, ECB, EVA)
with or without braces
extension up to 1500 mm
cutting the hem of the drain body
for a width of approx. 250 mm
(for DN 160, width approx. 315 mm)
custom cuff
(TPO/FPO, EPDM, ECB, EVA)
only without braces
extension up to 1000 mm
cutting the hem of the drain body:
DN 50 for a width of approx. 115 mm
DN 63 in width approx. 130 mm
DN 75 for a width of approx. 140 mm
DN 90 for a width of approx. 155 mm
DN 110 for a width of approx. 175 mm
DN 125 for a width of approx. 190 mm
custom cuff
(TPO/FPO, EPDM, ECB, EVA)
with or without braces
extension up to 1500 mm
cutting the hem of the drain body
for a width of approx. 250 mm
(for DN 160, width approx. 315 mm)
custom cuff
(TPO/FPO, EPDM, ECB, EVA) only without reinforcement
extension up to 1000 mm
cutting the hem of the drain body:
DN 50 for a width of approx. 115 mm
DN 63 in width approx. 130 mm
DN 75 for a width of approx. 140 mm
DN 90 for a width of approx. 155 mm
DN 110 for a width of approx. 175 mm
DN 125 for a width of approx. 190 mm
custom cuff
(TPO/FPO, EPDM, ECB, EVA)
with or without braces
custom cuff
(TPO/FPO, EPDM, ECB, EVA) only without reinforcement
extension up to 1500 mm
(base length 600 mm)
custom cuff
(TPO/FPO, EPDM, ECB, EVA) only without reinforcement
extension up to 1000 mm
(base length 500 mm)
possibility to produce a maximum size of 200 x 800 mm (50 mm each)
custom cuff
(TPO/FPO, EPDM, ECB, EVA) only without reinforcement
extension up to 1500 mm
(base length 600 mm)
custom cuff
(TPO/FPO, EPDM, ECB, EVA) only without reinforcement
extension up to 1000 mm
(base length 500 mm)
possibility to produce a maximum size of 200 x 800 mm (50 mm each)
light gray, dark gray,
Custom Foil
minimum quantity to order
50-100 pcs (depending on the type of modification)
possibility to make a height of 300 mm
minimum quantity to order
50-100 pcs (depending on the type of modification)
Other than the stated dimension
minimum quantity to order
50-100 pcs (depending on the type of modification)
light gray, dark gray,
Custom Foil
minimum quantity to order
50-100 pcs (depending on the type of modification)
possibility to make a height of 300 mm
minimum quantity to order
50-100 pcs (depending on the type of modification)
Other than the stated dimension
minimum quantity to order
50-100 pcs (depending on the type of modification)
manžeta na zakázku
(TPO/FPO, EPDM, ECB, EVA) pouze bez výztuhy
prodloužení nad manžetu
na 500 mm
barevné provedení
černé nebo bílé
(bez návaznosti na manžetu)
custom cuff
(TPO/FPO, EPDM, ECB, EVA) only without reinforcement
extension under the cuff
up to 1 500 mm
cutting the hem of the drain body:
DN 50 for a width of approx. 115 mm
DN 75 for a width of approx. 140 mm
DN 110 for a width of approx. 175 mm
DN 125 for a width of approx. 190 mm
DN 160 for a width of about 225 mm
manžeta na zakázku
(TPO/FPO, EPDM, ECB, EVA) pouze bez výztuhy
prodloužení nad manžetu
na 500 mm
prodloužení pod manžetu
do 1 000 mm
barevné provedení
černé nebo bílé
(bez návaznosti na manžetu)
manžeta na zakázku
(TPO/FPO, EPDM, ECB, EVA) pouze bez výztuhy
prodloužení nad manžetu
na 500 mm
prodloužení pod manžetu
do 1 000 mm
barevné provedení
černé nebo bílé
(bez návaznosti na manžetu)
možnost zvětšení kotevních otvorů na 20 mm (pro možnost kotvení teleskopickými kotvami),
barva dle požadované RAL
any PVC cuff
up to 1.5 mm thick with reinforcement
the possibility of increasing the anchor holes to 20 mm (for the possibility of anchoring with telescopic anchors),
color according to the required RAL
možnost vyrobit přířez z požadované folie
possibility to produce atypical height (max. 300 mm)
barva dle požadované RAL
(při změně RAL nejsou kotevní přířezy součástí)